Two Wests & Elliots Drip Irrigation Kits, Fittings, Nozzles and Watering Cans

15m Long - Weeping Garden Hose

Use this quality Weeping Garden Hose to create an effective garden watering system, ideal for watering crops such as tomatoes, strawberries, beans etc, in fact anything grown directly in the ground. A black, semi-flexible 1/2" (13mm) hose.  Gently 'weeps' water along its' entire length directly onto the soil. Use on the surface or bury beneath the ground (up to 6"/13cm), this helps to prevent water evaporation & also prolongs the life of the hose.  Runs off mains water. Use standard 1/2" (13mm) hosepipe & fittings (not supplied - available to purchase separately) to connect to the mains water supply. Environmentally friendly - it doesn't use much water & is made from recycled materials. Ideal for watering outdoor or indoor crops such as strawberries, peas, beans, tomatoes, cucumbers etc.  Can be laid in straight lines or snaked around a bed, directing water to the areas where it's most needed. For plants grown in beds run lines of hose approx. 18"-20" (46cm-51cm) apart. 15m Long - Weeping Garden Hose

Deluxe Misting Kit - 4' X 4'

By installing one of our high quality Deluxe Misting Kits in your greenhouse or polythene tunnel you will by able to easily & efficiently create a fine, even mist of water, ideal when propagating seedlings & cuttings. Widely & successfully used by commercial growers. Each kit is supplied complete with the following: Brass mist jet(s) - fully adjustable, these precision made jet(s) will provide a very fine, even mist. For efficient, long term use each jet has an in-built filter for easy cleaning. PVC Riser(s) - these lift the mist jet(s) approximately 20" (50cm) above the surface of the bench, enabling the mist to fall 'over' the plants. PVC Horizontal Tube(s) - each approximately 20" (50cm) in length, they are used to space the risers & rest on the surface of your bench. Threaded Connectors - supplied with all the necessary robust connectors to join horizontal tubes to rises & to fit mist jet(s) & hose inlet. PTFE tape - by fitting a small amount of tape around each joint makes assembly easier & ensures a watertight join.  Hose Inlet - enables a secure, watertight connection between your hose & the misting kit. Available in three sizes, the following number of mist jets are included with each kit: one jet with a 4' x 4' (1.2m x 1.2m) Kit, two jets with a 7' x 4' (2.1m x 1.2m) Kit & three jets with a 10' x 4' (3m x 1.2m) Kit. Buy Deluxe Misting Kit - 4' X 4'

Water Transport Sprinkler Starter Set (Gardena 1507-20)

This Gardena Water Transport Sprinkler Starter Kit provides everything needed to connect an outside tap to an oscillating sprinkler up to 40ft (12m) from the source. Contents: Tap Connector Set - 1 threaded tap adapter & two ó" Snap On Hose Connectors. 2 metres of ó" Hosepipe - to connect your outside tap to the Connection Point. Connection Point - to start off the Water Transport system. 20 metres ó" Piping - high quality, UV stabilised piping to join the Connection point to the Oscillating Sprinkler. 2 Hose Clips - used to grip ó" piping onto any of the joints to ensure permanent watertight connections. Pop-Up Oscillating Sprinkler - for effortless watering of square or rectangular areas, fully adjustable for areas 1440sq.ft (12-140mtr.sq.), spray widths 11-28ft (3.5-8.5m) & a range of 11-54ft (3.5-16.5m). Gardena product code: 1507-20. Buy W/Transport Sprinkler starter Set (Gardena 1507-20)

M2 - Spray Nozzle 90 Deg Pack of 5 (Gardena 1368-20)

These Gardena 90 degree Spray Nozzles are ideal for use in flower beds, borders or vegetable plots - by using in conjunction with 180 degree & 360 degree Spray Nozzles you can ensure complete coverage of a given area. The flow rate of the Nozzles is set at 45 litres per hour. Provides a light spray over a 90 degree area between approx. 6'6" (2m) up to 9'10" (3m). To control the length of the area covered insert a Control Valve (available to purchase separately) into which the Spray Nozzle can be screwed. Can be used by either: Inserting directly into the wall of " (13mm) Supply Tube. Fitting onto a " (13mm) Joint or Tube & Nozzle Peg. Or to lift the Nozzle higher use on top of a 9" (23cm) Pipe Extension (all these items are available to purchase separately). Gardena product code: 1368-20. Supplied as a pack of 5. Buy M2 - Spray Nozzle 90 Deg Pack of 5 (Gardena 1368-20)

M3 - Spray Nozzle 180 Deg Pack of 5 (Gardena 1367-20)

These Gardena 180 degree Spray Nozzles are ideal for use in flower beds, borders or vegetable plots - by using in conjunction with 90 degree degree & 360degree  Spray Nozzles you can ensure complete coverage of a given area. The flow rate of the Nozzles is set at 95 litres per hour. Provides a light spray over a 180 degree area between approx. 6'6" (2m) up to 9'10" (3m). To control the length of the area covered insert a Control Valve (available to purchase separately) into which the Spray Nozzle can be screwed. Can be used by either: Inserting directly into the wall of " (13mm) Supply Tube. Fitting onto a " (13mm) Joint or Tube & Nozzle Peg. Or to lift the Sprinkler higher use on top of a 9" (23cm) Pipe Extension (all these items are available to purchase separately). Gardena product code: 1367-20. Supplied as a pack of 5. Buy M3 - Spray Nozzle 180 Deg Pack of 5 (Gardena 1367-20)

M4 - Spray Nozzle 360 Deg Pack of 5 (Gardena 1365-20)

These Gardena 360 degree Spray Nozzles are ideal for use in flower beds, borders or vegetable plots - by using in conjunction with 90 degree & 180 degree Spray Nozzles you can ensure complete coverage of a given area. The flow rate of the Nozzles is set at 120 litres per hour. Provides a light spray over a 360 degree area between approx. 6'6" (2m) up to 9'10" (3m). To control the length of the area covered insert a Control Valve (available to purchase separately) into which the Spray Nozzle can be screwed. Can be used by either: Inserting directly into the wall of " (13mm) Supply Tube. Fitting onto a " (13mm) Joint or Tube & Nozzle Peg. Or to lift the Nozzle higher use on top of a 9" (23cm) Pipe Extension (all these items are available to purchase separately). Gardena product code: 1365-20. Supplied as a pack of 5. Buy M4 - Spray Nozzle 360 Deg Pack of 5 (Gardena 1365-20)

M5 - Spray Nozzle Mist Pack of 5 (Gardena 1371-20)

These Gardena 360 degree Micro Mist Nozzles are suitable for watering seedlings & delicate plants, making them ideal for use in greenhouses or cold frames. The flow rate of the Mist Nozzles is set at 15 litres per hour.  Provides a fine mist over a 360 degree area up to approx. 1'8" (0.5m). To control the length of the area covered insert a Control Valve (available to purchase separately) into which the Mist Nozzle can be screwed. Can be used by either: Inserting directly into the wall of " (13mm) Supply Tube. Fitting onto a " (13mm) Joint or Tube & Nozzle Peg. Or to lift the Sprinkler higher use on top of a 9" (23cm) Pipe Extension (all these items are available to purchase separately). Gardena product code: 1371-20. Supplied as a pack of 5. Buy M5 - Spray Nozzle Mist Pack of 5 (Gardena 1371-20)

M6 - Mid Spray Nozzle Strip Pack of 5 (Gardena 1370-20)

These Gardena Micro Mid Strip Spray Nozzles are suitable for watering long, narrow beds & borders or troughs. The flow rate of the Nozzles is set at 60 litres per hour. Provides a fine mist over long narrow areas in both directions up to approx. 18' (5.5m) by 2' (0.6m). To control the size of the area covered insert a Control Valve (available to purchase separately) into which the Mist Nozzle can be screwed. Can be used by either: Inserting directly into the wall of " (13mm) Supply Tube. Fitting onto a " (13mm) Joint or Tube & Nozzle Peg. Or to lift the Nozzle higher use on top of a 9" (23cm) Pipe Extension (all these items are available to purchase separately). Gardena product code: 1370-20. Supplied as a pack of 5. Buy M6 - Mid Spray Nozzle Strip Pack of 5 (Gardena 1370-20)

M7 - End Spray Nozzle Strip Pack of 5 (Gardena 1372-20)

These Gardena Micro End Strip Spray Nozzles are suitable for watering long, narrow beds & borders or troughs. The flow rate of the Nozzles is set at 45 litres per hour. Provides a fine mist over long narrow areas in one direction up to approx. 9' (2.75m) by 2' (0.6m). To control the size of the area covered insert a Control Valve (available to purchase separately) into which the Mist Nozzle can be screwed. Can be used by either: Inserting directly into the wall of " (13mm) Supply Tube. Fitting onto a " (13mm) Joint or Tube & Nozzle Peg. Or to lift the Nozzle higher use on top of a 9" (23cm) Pipe Extension (all these items are available to purchase separately). Gardena product code: 1372-20. Supplied as a pack of 5. Buy M7 - End Spray Nozzle Strip Pack of 5 (Gardena 1372-20)

M8 -Adjustable Spray Nozzle Pack of 2 (Gardena 1396-20)

These versatile Gardena 6 Pattern Adjustable Spray Nozzles are suitable for use in flower beds, borders or vegetable plots & enable you to select the exact area to water with ease. The flow rate of the Nozzles is set at 35 litres per hour. Providing a fine spray, the nozzle can be adjusted to cover either a: 90 degree area up to 8' (2.5m) diameter. 180 degree area up to 8' (2.5m) diameter. 270 degree area up to 8' (2.5m) diameter. 360 degree area up to 6'6" (2m) diameter. Over a long narrow area in one direction up to approx. 16'6" (5m) by 3'3" (1m).  Over a long narrow area in both directions up to approx. 8' (2.5m) by 3'3" (1m). To control the size of the area covered insert a Control Valve (available to purchase separately) into which the Spray Nozzle can be screwed. Gardena product code: 1396-20. Supplied as a pack of 2. Buy M8 -Adjustable Spray Nozzle Pack of 2 (Gardena 1396-20)

3/16" Branch Tube - Per Metre | Two Wests

When creating an automatic watering system for your garden or greenhouse use this robust Gardena 3/16" (4.6mm) Branch Tube to carry water to individual plants, tubs, troughs, hanging baskets etc.High quality, UV stabilised 3/16" (4.6mm) unobtrusive black tubing. Use when creating a mains drip & spray watering system to take the water from the main " (13mm) supply tube to individual subjects, containers, hanging baskets etc. Both In Line & End Line Drippers are available to fit directly into the branch tube. To easily connect the branch tube to the supply tube use Gardena's specially designed tube connectors (available to purchase separately). Or in situations where it is important that the tubing is inconspicuous use the branch tube as the main artery of the system - but remember the water flow will be restricted, making the distance the tube can be run & the number of drippers inserted will be limited. Can be used above & below ground. Gardena product codes: 1350-20 (15 metre coil), 1348-20 (50 metre coil). Supplied either per metre, or in coils of 15 metre or 50 metre lengths, simply purchase as many metres as required. Buy 3/16" Branch Tube - Per Metre

1/2" Supply Tube - Per Metre (0268-037)

Forming the main artery of automatic watering systems this strong Gardena «" (13mm) Supply Tube securely carries water from the tap to where it's required in greenhouse or garden. High quality, UV stabilised «" (13mm) strong black tubing. Can be used above & below ground (buried in soil or compost or covered with mulch). When laying the supply tube around your greenhouse or garden use the specially designed connectors to route the tube around corners or to create branches without restricting the flow of water.

To prevent the tube from moving out of position use tube pegs (to hold the tube against soil) or clips (to retain the tube on firm surfaces). Use the specially designed drippers & spray nozzles directly into the wall of the supply tube or connect 3/16" (4.6mm) branch tube & insert drippers etc into this less conspicuous tubing. When operating from a single tap Gardena recommend using. Up to a maximum of 120 metres when watering with drip heads ONLY. Up to a maximum of 30 metres when watering with a mixture of drippers, spray nozzles & sprinklers. Gardena product codes: 1346-20 (15 metre coil), 1347-20 (50 metre coil). Supplied either per metre, or in coils of 15 metre or 50 metre lengths, simply purchase as many metres as required. Buy 1/2" Supply Tube - Per Metre (0268-037)

Deluxe Mist Jet (3002002)

A precision-made, fully adjustable Deluxe Mist Jet which produces a very fine, even mist & enables you to create your own misting system or mist propagation system for use in a greenhouse or polythene tunnel. Provides coverage of 3'-4'6" (91-137cm) depending on the water pressure. Threaded at the base for screwing into a " (13mm) threaded connector or tube. Removable filter for easy cleaning. For cleaning of the jet orifice the striking pin can be moved sideways. Dimensions: 3¬" (8.5cm) wide, 3" (8cm) high & 5/8" (1.5cm) deep. Please note: designed to run off mains water or a good pumped supply. Deluxe Mist Jet (3002002)

M1 - Roto Sprinkler Pack of 2 (Gardena 1369-20)

These mini Gardena 360 degree Roto Sprinklers are ideal for use in flower beds, borders or vegetable plots. The flow rate of the Sprinklers is set at 85 litres per hour. Provides a fine spray over a circular area of between approx. 5ft (1.5m) up to 11'6" (3.5m). To control the length of the area covered insert a Control Valve (available to purchase separately) into which the Sprinkler can be screwed. Can be used by either: Inserting directly into the wall of " (13mm) Supply Tube. Fitting onto a " (13mm) Joint or Tube & Nozzle Peg. Or to lift the Sprinkler higher use on top of a 9" (23cm) Pipe Extension (all these items are available to purchase separately). Gardena product code: 1369-20. Supplied as a pack of 2. Buy M1 - Roto Sprinkler Pack of 2 (Gardena 1369-20)

8' Long - 10' Wide Overhead Spray Kit - Total Coverage

Automatically water your plants with ease by installing one of our Overhead Spray Kits. By generally spraying throughout the greenhouse or poly tunnel you will help to promote healthy plant growth by providing water to both the base of the plants & their foliage. General spray watering is favoured by many commercial growers as it not only waters the plants but also helps to reduce the temperature in tunnels or greenhouses lacking ventilation. Designed for use in 10' (3.03m) wide greenhouses or poly tunnels the kit includes: Fixing supports & bolts - to attach to the framework of the greenhouse near the ridge to hold the suspension hooks.  Metal suspension hooks - to suspend from the fixing supports, securely holding the system just below the ridge of your greenhouse.  Rigid PVC tubing - with pre-drilled holes to take the nozzles & with all the connectors required (already attached). Snap-on brass hose coupling - used to connect «" (13mm) hose pipe (available to purchase separately) to the PVC tube. Spray nozzles - 360§ nozzles are supplied with overhead spray kits for total coverage (spraying the entire greenhouse). For half coverage (to water one side of the greenhouse) the kits are supplied complete with 180§ nozzles.  Kits are available to suit greenhouses 8' (2.44m), 10' (3.03m), 12' (3.66m), 15' (4.57m), 20'(6.10m) , 25' (7.62m), 30' (9.14m) or 35' (10.67m) long. Buy 8' Long - 10' Wide Overhead Spray Kit - Total Coverage

15' Wide Overhead Spray Kit - 15' Long - Half Coverage

An automatic watering system for plants in your greenhouse or polytunnel. These Overhead Spray Kits have been designed to fit within wider greenhouses or tunnels as they can water areas up to 15ft (4.5m) wide. They create a general spray of water within the area so your plants benefit from water around their base and on their foliage. General spray watering is favoured by many commercial growers as it not only waters the plants but also helps to reduce the temperature in tunnels or greenhouses lacking ventilation. Each kit includes:  Fixing supports & bolts - to attach to the roof glazing bars of the greenhouse to hold the suspension hooks. Metal suspension hooks - to suspend from the fixing supports, securely holding the system near the roof of your greenhouse. Rigid PVC tubing - with pre-drilled holes to take the nozzles & with all the connectors required (already attached). Snap-on brass hose coupling - used to connect «" (13mm) hose pipe (available to purchase separately) to the PVC tube. Spray nozzles - 360§ nozzles are supplied with overhead spray kits for total coverage (spraying the entire greenhouse). For half coverage (to water down either side of the greenhouse and not down the centre) the kits are supplied complete with 180§ nozzles.  Kits are available to suit greenhouses 15' (4.57m), 20'(6.10m) , 25' (7.62m), 30' (9.14m) or 35' (10.67m) long. Buy 15' Wide Overhead Spray Kit - 15' Long - Half Coverage

B- Master Unit Filter (Gardena 1355)

When installing a Gardena Drip & Spray System a Master Unit should be fitted at the start of the system to filter & reduce the mains water pressure to 21psi (1.5 bar) which efficiently operates micro-jets, sprinklers & drippers. One end of the unit has a coupling enabling it to be simply pushed into a Snap-On connector on the end of hosepipe attached to your mains water supply. Supplied with fittings to enable either " (13mm) Supply Tube or 3/16" (4.6mm) Branch Tube to be fitted directly to the unit. A stainless steel clip enables quick & easy connection or disconnection to the tube. Includes a removable filter which should be cleaned periodically to ensure efficient operation. Gardena product code: Master Unit 1000 / 1355. Buy B- Master Unit (Gardena 1355)

E1 - 1/2" Straight Connectors Pack of 3 (Gardena 8356-20)

Use these robust, Gardena " (13mm) Straight Connectors to easily & securely join two pieces of " supply tube together.  Design includes stainless steel clips to enable quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8356-20. Supplied at a pack of 3. Buy E1 - 1/2" Straight Connectors Pack of 3 (Gardena 8356-20)

E2 - 1/2" Elbow Connectors Pack of 2 (Gardena 8382-20)

Use these robust Gardena " (13mm) Elbow Connectors to maintain a smooth flow of water through the " supply tube, where a right angle turn is required in the layout of the tube. Design includes stainless steel clips enabling quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8382-20. Supplied as a pack of 2. Buy E2 - 1/2" Elbow Connectors Pack of 2 (Gardena 8382-20)

E6 - 3/16" Straight Connector Pack of 10 (Gardena 8337-20)

These dual purpose Gardena 3/16" (4.6mm) Straight Connectors can be used to either connect two pieces of 3/16" branch tube or to connect branch tube into " (13mm) supply tube.  When using these connectors to attach /branch 3/16" (4.6mm) tube into " (13mm) supply tube use an installation tool (available separately) to create a neat hole in the supply tube. Use the screw threaded end of the connector to securely fit the connector into the hole created. Design includes stainless steel clips enabling quick & easy connection or disconnection to branch tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8337-20. Supplied as a pack of 10. Buy E6 - 3/16" Straight Connector Pack of 10 (Gardena 8337-20)

E3 - 1/2" 'T' Connectors Pack of 2 (Gardena 8329-20)

Use these sturdy Gardena " (13mm) T Connectors with " supply tube where you want to securely 'branch' the tube in three directions. Design includes stainless steel clips enabling quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8329-20. Supplied as a pack of 2. Buy E3 - 1/2" 'T' Connectors Pack of 2 (Gardena 8329-20)

E9- 3/16" 'T' Connector Pack of 10 (Gardena 8330-20)

Use these sturdy Gardena 3/16" (4.6mm) T Connectors with 3/16" (4.6mm) branch tube where you want to 'branch' the tube in three directions without affecting the smooth flow of water. Design includes stainless steel clips enabling quick & easy connection or disconnection to branch tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8330-20. Supplied as a pack of 10. Buy E9- 3/16" 'T' Connector Pack of 10 (Gardena 8330-20)

E4 - 1/2" 4 Way Connectors Pack of 2 (Gardena 8339-20)

Where you need to securely branch " supply tube in four directions use these robust Gardena " (13mm) 4 Way Connectors. Design includes stainless steel clips enabling quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8339-20. Supplied as a pack of 2. Buy E4 - 1/2" 4 Way Connectors Pack of 2 (Gardena 8339-20)

E7 - 3/16" 4 Way Connector Pack of 10 (Gardena 8334-20)

Design includes stainless steel clips enabling quick & easy connection or disconnection to branch tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8334-20. Supplied as a pack of 10. Buy E7 - 3/16" 4 Way Connector Pack of 10 (Gardena 8334-20)

E5 -1/2" To 3/16" Reducing 'T' Pack of 5 (Gardena 8333-20)

When laying out your automatic watering system these robust Gardena 3 Way Connectors enable you to branch 3/16" (4.6mm) branch tube into " (13mm) supply tube, allowing you to take water direct to plants, containers or baskets with this discreet tube. Gardena advise you should not run more than 15 metres in a single length/ branch from the supply tube due to the water flow being restricted when using this narrow 3/16" (4.6mm) tube. Design includes stainless steel clips enabling quick & easy connection or disconnection to supply tube & branch tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8333-20. Supplied as a pack of 5. Buy E5 -1/2" To 3/16" Reducing 'T' Pack of 5 (Gardena 8333-20)

E8 - 3/16" Elbow Connector Pack of 10 (Gardena 8381-20)

Use these robust, Gardena 3/16" (4.6mm) Elbow Connectors to maintain a smooth flow of water through the 3/16" (4.6mm) branch tube when a right angle turn is required in the layout of the tube. Design includes stainless steel clips enabling quick & easy connection or disconnection to branch tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8381-20. Supplied as a pack of 10. Buy E8 - 31/6" Elbow Connector Pack of 10 (Gardena 8381-20)

F1 - 1/2" Plug Pack of 5 (Gardena 8324-20)

Use these robust Gardena " (13mm) Plugs at the end of " Supply Tube to end a run. Design includes a stainless steel clip enabling quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8324-20. Supplied as a pack of 5. Buy F1 - 1/2" Plug Pack of 5 (Gardena 8324-20)

N1- 1/2" Nozzle / Pipe Joint pack of 5 (Gardena 8331-20)

Versatile 1/2" (13mm) Spray Nozzle & Pipe Joints designed by Gardena to allow you to quickly, easily & securely fit Spray Nozzles into " Supply Tube. The versatile design of the joints enables them to: Be securely held in place on either soft ground or a hard surface - by combining them with either 1/2" (13mm) Tube & Nozzle Pegs or Tube Clamps (available to purchase separately). Enable Pipe Extensions to be fitted to lift Spray Nozzles 9" (23cm) above the ground. Allow you to change Spray Nozzles easily as your watering requirements alter. Gardena product code: 8331-20. Supplied as a pack of 5. Buy N1- 1/2" Nozzle / Pipe Joint pack of 5 (Gardena 8331-20)

N3 - 3/16" Nozzle / Pipe Joint Pack of 5 (Gardena 8332-20)

Versatile 3/16" (4.6mm) Spray Nozzle & Pipe Joints designed by Gardena to allow you to quickly, easily & securely fit Spray Nozzles into 3/16" (4.6mm) Branch Tube. The design of the joints enables them to: Be securely held in place on either soft ground or a hard surface by combining them with 3/16" (4.6mm) Tube & Nozzle Pegs or Tube Clamps (available to purchase separately). Enable Pipe Extensions to be fitted to lift Spray Nozzles 9" (23cm) above the ground. Allows you to change Spray Nozzles easily as your watering requirements alter.  Gardena product code: 8332-20. Supplied as a pack of 5. Buy N3 - 3/16" Nozzle / Pipe Joint Pack of 5 (Gardena 8332-20)

1/2" Straight Connector For Weeping Hose (0300-020)

Use this robust, barbed black plastic «" Straight Connector to join two pieces of «" Weeping Garden Hose. Manufactured from robust black plastic.  Barbed at both sides to ensure a tight, secure joint between both pieces of hose. Dimensions: 1ó" (4.5cm) long. Buy 1/2" Straight Connector For Weeping Hose (0300-020)

1/2" Elbow Connector For Weeping Hose (0822-002)

Use this sturdy, black plastic Elbow Connector to create an efficient right angled joint when creating a layout with the «" Weeping Garden Hose. Manufactured from robust black plastic.  Barbs on the joint help to create a secure fitting between the Hose & Connector. Dimensions: 1ó" (4.5cm) in either direction. Buy 1/2" Elbow Connector For Weeping Hose (0822-002)

1/2" Tee Connector For Weeping Hose (0822-015)

When creating a layout with the Weeping Garden Hose, this «" T Connector can be used to 'branch' the Hose. Manufactured from robust black plastic.  Barbs on the joint help to create a secure fitting between the Hose & Connector. Dimensions: approximately 1" (2.5cm) long in all three directions. Buy 1/2" Tee Connector For Weeping Hose (0822-015)

1/2" End Plug For Weeping Hose (0244-020)

A 1/2" Plug designed to end a length of Weeping Garden Hose. Manufactured from robust black plastic. Dimensions: 1" (2.5cm) long. 1/2" End Plug For Weeping Hose (0244-020)

N2- Joint (9") Extension Pipe Pack of 5 (Gardena 1377-20)

Increase the versatility of Gardena's Spray Nozzles by installing them on top of these 9" (23cm) Pipe Extensions. The design of these extensions enables them to be either: Inserted directly into the wall of «" (13mm) Supply Tube. Or for a more secure connection on either soft ground or a hard surface use together with Spray Nozzle Joints, Tube & Nozzle Pegs or Tube Clamps (available to purchase separately). Gardena product code: 1377-20. Supplied as a pack of 5. Buy N2- Joint (9") Extension Pipe Pack of 5 (Gardena 1377-20)

Q4 - 1/2" Clamps For N1 Pack of 2 (Gardena 8380-20)

Robust 1/2" (13mm) Clamps designed by Gardena to hold Supply Tube, Joints & Spray Nozzles to a firm surface. To fit over either 1/2" (13mm) Straight Connectors, 1/2" (13mm) Elbow Connectors, 1/2" (13mm) T Connectors or 1/2" (13mm) Spray Nozzle Joints - with or without Pipe Extensions - to hold the 1/2" (13mm) Supply Tube or Spray Nozzles securely in position against a firm surface (wood, stone etc). A pre-formed hole in each Clamp enables you to use a screw (not supplied) to anchor the clamp in place.  Where joints have been fitted into tube - whether to branch off or turn a corner - using these clamps will prevent the tube from moving out of place. When placed where Spray Nozzles are positioned, the Nozzle will be securely held in place ensuring they remain in the most efficient position for watering your plants. Gardena Product Code: 8380-20 Supplied as a pack of 2. Buy Q4 - 1/2" Clamps For N1 Pack of 2 (Gardena 8380-20)

Q5 - 3/16" Clamps For N2 Pack of 5 (Gardena 8379-20)

Versatile 3/16" (4.6mm) Tube Clamps designed by Gardena to securely hold branch tube, joints & spray nozzles to a firm surface. To fit over either 3/16" (4.6mm) Straight Connectors, 3/16" (4.6mm) Elbow Connectors, 3/16" (4.6mm) T Connectors or 3/16" (4.6mm) Spray Nozzle Joints - with or without Pipe Extensions - to hold the 3/16" (4.6mm) Branch Tube or Spray Nozzles securely in position against a firm surface (wood, stone etc).  A pre-formed hole in each Clamp enables you to use a screw (not supplied) to anchor the clamp in place. Where joints have been fitted into tube - whether to branch off or turn a corner - using these clamps will prevent the tube from moving out of place. When placed where Spray Nozzles are positioned, the Nozzle will be securely held in place ensuring they remain in the most efficient position for watering your plants. Gardena product code: 8379-20. Supplied as a pack of 5. Buy Q5 - 3/16" Clamps For N2 Pack of 5 (Gardena 8379-20)

F2 - 3/16" Plug Pack of 10 (Gardena 1323-20)

Screw these robust Gardena 3/16" (4.6mm) Plugs at the end of 3/16" (4.6mm) Branch Tube to end a run.  Can also be used to securely seal unwanted holes in the supply tube if you modify your watering system. Gardena product code: 1323-20. Supplied as a pack of 10. Buy F2 - 3/16" Plug Pack of 10 (Gardena 1323-20)

L6 - End-Line Dripper 4L Pack of 25 (Gardena 1341-20)

Use these Gardena 4 Litre End-Line Drippers either at the end of 3/16" (4.6mm) Branch Tube or use directly in the side of " (13mm) Supply Tube. Drippers are used to provide a regular, measured 'drip' of water at the base of the plant. |The flow rate of the Drippers is set at 4 litres per hour. They are ideal for use in hanging baskets or containers as well as being suitable for use along hedges or for watering individual plants in beds or borders. Gardena product code: 1341-20. Supplied as a pack of 25. Buy L6 - End-Line Dripper 4L Pack of 25 (Gardena 1341-20)

G1 - 1/2" Shut-Off Valve X1 (Gardena 8358-20)

This Gardena " (13mm) Shut-Off Valve can be fitted into the Supply Tube to enable areas in your watering system to be isolated as required. Especially useful if you're planning a large watering system in a garden or greenhouse. Design includes stainless steel clips enabling quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8358-20. Buy G1 - 1/2" Shut-Off Valve X1 (Gardena 8358-20)

G1 - 1/2" Shut-Off Valve X1 (Gardena 8358-20)

This Gardena " (13mm) Shut-Off Valve can be fitted into the Supply Tube to enable areas in your watering system to be isolated as required. Especially useful if you're planning a large watering system in a garden or greenhouse. Design includes stainless steel clips enabling quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8358-20. Buy G1 - 1/2" Shut-Off Valve X1 (Gardena 8358-20)

G2 - 3/16" Shut-Off Valve Pack of 2 (Gardena 8357-20)

Insert these Gardena 3/16" (4.6mm) Shut-Off Valves in the Branch Tube of you're watering system to enable you to isolate areas in your watering system quickly & easily. Simply turning the control switch on the top of the value will stop water flowing beyond the valve. Design includes stainless steel clips enabling quick & easy connection or disconnection to supply tube, so if your watering needs increase within the garden or greenhouse extending or modifying the system is simple. Gardena product code: 8357-20. Supplied as a pack of 2. Buy G2 - 3/16" Shut-Off Valve Pack of 2 (Gardena 8357-20)

P - Control Valve Pack of 5 (Gardena 1374-20)

Versatile Control Valves designed by Gardena to control flow rate & coverage of spray nozzles. Fit directly into the wall of «" (13mm) Supply Tube, into Spray Nozzle Joints, Tube & Nozzle Pegs or Pipe Extensions (all available to purchase separately) in order to control the flow of water . Using Control Values enables you to adjust the amount of water available to Spray Nozzles, so regulating their flow rate & coverage. Gardena product code: 1374-20. Supplied as a pack of 5. P - Control Valve Pack of 5 (Gardena 1374-20)

H1 - 1/2" Tube / Nozzle Peg Pack of 3 (8328-20)

These versatile Gardena " (13mm) Tube & Nozzle Pegs have been designed to hold " Supply Tube or Sprinklers / Nozzles securely in place. Can be used to hold the Supply Tube in place into the ground - the 5" (13cm) 'leg' on the base of the peg can be sunk into the ground to securely hold the tube whilst the top of the unit clips over straight tube or " Connectors. The design of the pegs also enables them to be used to hold sprinklers in place - whether they have been fitted directly into the Supply Tube or on the end of Pipe Extensions - the hole at the top of the peg simply slips over the sprinkler or enables the pipe extension to be fitted. Gardena product code: 8328-20. Supplied as a pack of 3. Buy H1 - 1/2" Tube / Nozzle Peg Pack of 3 (8328-20)

H3- 3/16" Tube / Nozzle Peg Pack of 3 (Gardena 8327-20)

These versatile Gardena 3/16" (4.6mm) Tube & Nozzle Pegs have been designed to hold 3/16" Branch Tube or Sprinklers / Nozzles securely in place.  Use to hold the Branch Tube in place into the ground - the 4" (10cm) 'leg' on the base of the peg can be sunk into the ground to securely hold the tube whilst the top of the unit clips over straight tube or 3/16" Connectors.  Can also be used to hold sprinklers in place - whether they have been fitted directly into the Branch Tube via Spray Nozzle Joints or on the end of Pipe Extensions - the hole at the top of the peg simply slips over the sprinkler or enables the pipe extension to be fitted. Gardena product code: 8327-20. Supplied as a pack of 3. Buy H3- 3/16" Tube / Nozzle Peg Pack of 3 (Gardena 8327-20)

H2 - 3/16" Peg Pack of 10 (Gardena 1327-20)

Use these Gardena 3/16" (4.6mm) Tube Pegs to hold the Branch Tube securely in place. Simply clip the tube into the top of the peg & sink the 3" (9cm) 'leg' of the peg into the ground. Using these clips enables you to form gentle curves in the layout of your watering system.  By placing them close to sprinklers or spray nozzles prevents them from moving when in use. Gardena product code: 1327-20. Supplied as a pack of 10. Buy H2 - 3/16" Peg Pack of 10 (Gardena 1327-20)

K - Installation Tool 1322

This robust Installation Tool is essential for easy installation of drippers & micro jets in Gardena's Drip & Spray Watering System. Use to: Make suitable holes in supply tube for direct insertion of drippers & micro jets. To 'screw' these into position in the holes or end of branch tube.  Gardena product code: 1322. Buy K - Installation Tool 1322

L1 In-Line Adjustable Dripper Pack of 10 (Gardena 8392-20)

Use these Gardena In-Line Adjustable Drippers in 3/16" (4.6mm) Branch Tube, the flow rate is adjustable between 0-20 litres per hour by turning the orange head of the dripper. Simply fit the tube on either side of the dripper. Drippers are used to provide a regular, measured 'drip' of water at the base of the plant. |They are ideal for use in hanging baskets or containers as well as being suitable for use along hedges or for watering individual plants in beds or borders. Gardena product code: 8392-20. Supplied as a pack of 10. An end cap is included in every pack of ten Drippers so one of the In-Line Drippers can be fitted with the cap to create an end line dripper. L1 In-Line Adjustable Dripper Pack of 10 (Gardena 8392-20)

L2 - In-Line Dripper 2L Pack of 10 (Gardena 8343-20)

Use these Gardena In-Line Drippers in 3/16" (4.6mm) Branch Tube, the flow rate of the Drippers is set at 2 litres per hour. Simply fit the tube on either side of the dripper. Drippers are used to provide a regular, measured 'drip' of water at the base of the plant. |They are ideal for use in hanging baskets or containers as well as being suitable for use along hedges or for watering individual plants in beds or borders. Gardena product code: 8343-20. Supplied as a pack of 10. An end cap is included in every pack of ten Drippers so one of the In-Line Drippers can be fitted with the cap to create an end line dripper. Buy L2 - In-Line Dripper 2L Pack of 10 (Gardena 8343-20)

L3 - In-Line Dripper 4L Pack of 10 (Gardena 8344-20)

The flow rate of these Gardena In-Line Drippers is set at 4 litres per hour, simply insert into 3/16" (4.6mm) Branch Tube, fitting the tube to either side of the dripper. Drippers are used to provide a regular, measured 'drip' of water at the base of the plant. |They are ideal for use in hanging baskets or containers as well as being suitable for use along hedges or for watering individual plants in beds or borders. Gardena product code: 8344-20. Supplied as a pack of 10. An end cap is included in every pack of ten Drippers so one of the In-Line Drippers can be fitted with the cap to create an end line dripper. Buy L3 - In-Line Dripper 4L Pack of 10 (Gardena 8344-20)

L4 End-Line Adjustable Dripper (10 Pack) (Gardena 1391-20)

Use these versatile Gardena Adjustable End-Line Drippers either at the end of 3/16" (4.6mm) Branch Tube or use directly in the side of " (13mm) Supply Tube. Drippers are used to provide a regular, measured 'drip' of water at the base of the plant. |The flow rate is adjustable between 0-20 litres per hour by turning the orange head of the dripper. They are ideal for use in hanging baskets or containers as well as being suitable for use along hedges or for watering individual plants in beds or borders. Gardena product code: 1391-20. Supplied as a pack of 10. Buy L4 End-Line Adjustable Dripper (10 Pack) (Gardena 1391-20)

L5 - End-Line Dripper 2L Pack of 25 (Gardena 1340-20)

Use these Gardena 2 Litre End-Line Drippers either at the end of 3/16" (4.6mm) Branch Tube or use directly in the side of " (13mm) Supply Tube. Drippers are used to provide a regular, measured 'drip' of water at the base of the plant. |The flow rate of the Drippers is set at 2 litres per hour. They are ideal for use in hanging baskets or containers as well as being suitable for use along hedges or for watering individual plants in beds or borders. Gardena product code: 1340-20. Supplied as a pack of 25. Buy L5 - End-Line Dripper 2L Pack of 25 (Gardena 1340-20)

Tropf Blumat Probes M (3510)

The Tropf Blumat Ceramic Probe is the secret of the Tropf Blumat Drip Watering System, regulating the flow of water at point of watering. Place a Ceramic Probe into the 1/16" Drip Tube in the Drip Watering System where you require a watering point. Plunged into the plants growing media the Probe senses the moisture content. If dry then water is dripped onto the surface, when wet the drip watering ceases. For varying water requirements of different plant types the rate of drip is adjustable at the Probe. A single Probe is sufficient to water an area of up to 10" (25cm) in diameter (e.g. hanging basket, pot etc). If watering plants with similar needs the coverage may be extended by up to approximately 3ft x 10" (100cm x 25cm) by using Drippers (available to purchase separately). Dimensions: overall length 5" (13cm). Buy Tropf Blumat Probes M (3510)

Tropf Blumat Mains Kit (Hose)

This Tropf Blumat Mains Kit Hose contains sufficient components to water 12 hanging baskets, or 12 tubs, or 4 grow bags or a 10ft x 8" (3m x 20cm) bed etc. when connected to a «" hosepipe supplied from either mains water or an overhead tank. Contents: Pressure Reducer - supplied with fittings for a connection onto a hosepipe. 12 Probes - these regulate the flow of water at point of watering. 11 In-Line Connectors - to connect drip tube to feed tube (1 is required for each probe).  1 End-Line Connector. 10 Metres ¬" Feed Tube - this forms the main artery of the system, carrying the water around. 3 Metres 1/16" Drip Tube - carries water from the Feed Tube up to & through a probe & delivers the drips. Buy Tropf Blumat Mains Kit (Hose)

Tropf Blumat Mains Kit (Tap)

This Tropf Blumat Mains Kit Tap contains sufficient components to water 12 hanging baskets, or 12 tubs, or 4 grow bags or a 10ft x 8" (3m x 20cm) bed etc. with water being supplied from an outside tap. Contents: Pressure Reducer - to fit a ó" screw threaded mains water tap. 12 Probes - these regulate the flow of water at point of watering. 11 In-Line Connectors - to connect the drip tube to the feed tube (1 is required for each probe). 1 End-Line Connector. 10 Metres ¬" Feed Tube - this forms the main artery of the system, carrying the water around. 3 Metres 1/16" Drip Tube - carries water from the Feed Tube up to & through a probe & delivers the drips. Buy Tropf Blumat Mains Kit (Tap)

Tropf Blumat Tank Kit

This Tropf Blumat Tank Kit contains sufficient components to water 12 hanging baskets, or 12 tubs, or 4 grow bags or a 10ft x 8" (3m x 20cm) bed etc from a tank of water. Contents: Tank Connector - to give a ¬" outlet from an overhead tank. 12 Probes - these regulate the flow of water at point of watering. 11 In-Line Connectors - to connect drip tube to feed tube (1 required for each probe). 1 End-Line Connector. 10 Metres ¬" Feed Tube - this forms the main artery of the system, carrying the water around. 3 Metres 1/16" Drip Tube - carries water from the Feed Tube up to & through a probe & delivers the drips. Buy Tropf Blumat Tank Kit

Tropf Blumat Pressure Reducer A (36001)

The Tropf Blumat Watering System operates on a maximum water pressure of 1 bar (down to a minimum of 0.5 bar). In order to achieve this when running the system from a mains water tap you need to use a Pressure Reducer. Fitting to a Tap: The top of the Pressure Reducer simply screws onto a ó" screw threaded tap. If your tap is a different size - 1/2" or 5/8" - you will need to purchase a set of adapters (available separately) to fit into the top of the Pressure Reducer prior to fitting to the tap.  Fitting the " Tube: At the base of the Pressure Reducer just unscrew the retaining cap & thread onto the ¬" tube. Push the ¬" tube onto the barbed fitting & screw the retaining cap back onto the Pressure Reducer to hold the tube securely in place. Water Filter - within the Pressure Reducer is a water filter to prevent any small particles getting into the watering system & blocking the tube or nozzles. The filter is easily accessible for simple cleaning. Buy Tropf Blumat Pressure Reducer A (36001)

Tropf Blumat Pressure Reducer Hose B

If you need to start the Tropf Blumat system from a «" hosepipe (for example if you are using the system in a greenhouse which is a distance from your mains water supply) this Pressure Reducer is supplied complete with the fittings to allow you to do so.  Fitting to the Hose: Fit the Gardena Snap-On Hose Connector to the end of your existing «" hosepipe. This high quality Gardena connector has a special black hose sleeve which fits over the end of the hose helping to retain the hose (even thin walled types) even more securely. For ease in use the connector has soft plastic 'pimpled' grip areas for a secure pull-release mechanism. Into the top of the Pressure Reducer screw the grey adaptor. This will then allow you to push the Snap-On Hose Connector onto the Pressure Reducer. Fitting the ¬" Tube: At the base of the Pressure Reducer just unscrew the retaining cap & thread onto the ¬" tube. Push the ¬" tube onto the barbed fitting & screw the retaining cap back onto the Pressure Reducer to hold the tube securely in place. Water Filter - within the Pressure Reducer is a water filter to prevent any small particles getting into the watering system & blocking the tube or nozzles. The filter is easily accessible for simple cleaning. Buy Tropf Blumat Pressure Reducer Hose B

Tropf Blumat Tank Connector

If you wish to operate the Tropf Blumat Watering System from a 'tank' of water rather than mains water, you will need a Tank Connector to allow you to attach the ¬" tubing direct to the water supply. The robust Tank Connector is simple to install. Unscrew the Tank Connector so that you have three separate parts ready to fit: A - A 2" (5cm) long screwed fitting which should be fitted through the side or base of the tank after drilling an 11mm hole (you will need access to the inside of the tank in order to fit this). B - Rubber washer to fit onto the outside of the tank. C - screw fitting to attach back to the Tank Connector of the outside of the tank, screw tight up to the washer for a secure connection. You are then ready to fit the ¬" tubing to the barbed fitting at the end of the Tank Connector. Buy Tropf Blumat Tank Connector

Tropf Blumat In-Line Dripper N (4300)

Use Tropf Blumat In-Line Drippers in conjunction with a ceramic probe to water larger hanging baskets, containers, troughs & beds. Drippers are fitted in the 1/16" Drip Tube after a ceramic Probe. In-line Drippers are barbed at either side to hold the 1/16" tube securely in place. Up to a maximum of five Drippers can be fitted into 3ft (1m) of 1/16" drip tube. The Drippers are NOT adjustable - the rate of water is adjusted at the Ceramic Probe. To maintain efficiency the black screw on the top of the Dripper can be removed for cleaning. Dimensions: 1" (2.5cm) high x 3/8" (1cm) wide. Buy Tropf Blumat In-Line Dripper N (4300)

Tropf Blumat End-Line Dripper O (4301)

Fit a Tropf Blumat End-Line Dripper into the end of 1/16" Drip Tube to form the last drip point at the end of a run. Barbed at one side to fit securely into the end of 1/16" tube. The Drippers are NOT adjustable - the rate of water is adjusted at the Ceramic Probe. To maintain efficiency the black screw on the top of the Dripper can be removed for cleaning. Dimensions: 1" (2.5cm) high x 3/8" (1cm) wide. Buy Tropf Blumat End-Line Dripper O (4301)

Tropf Blumat 1/4" Straight Connector E

This Tropf Blumat 1/4" Straight Connector is used to join 1/4" tube to ¬" tube. Manufactured from robust black plastic. Barbed at either end to hold the 1/4" tube securely in place.  Dimensions: 4cm long. Buy Tropf Blumat 1/4" Straight Connector E

Tropf Blumat 1/4" Elbow Connector F

Use a Tropf Blumat 1/4" Elbow Connector in the Tropf Blumat Drip Watering System to take 1/4" tube neatly round a corner or a sharp bend. Manufactured from robust black plastic. Barbed at either end to hold the 1/4" tube securely in place. Dimensions: «" (1.5cm) long in either direction. Buy Tropf Blumat 1/4" Elbow Connector F

Tropf Blumat 1/4" T Connector G

A Tropf Blumat 1/4" T Connector enables water to flow easily into a number of areas. Use where you need to divert water into two different areas. Manufactured from robust black plastic.  Barbed at on all three sides to hold the 1/4" tube securely in place.  Dimensions: «" (1.5cm) long on all three sides. Tropf Blumat 1/4" T Connector G

Tropf Blumat In-Line Connector J (3517)

A Tropf Blumat In-Line Connector enables ¬" Feed Tube to continue to travel in a straight line whilst 1/16" Drip Tube is branched off to enable a Ceramic Probe to be fitted. Use where you need to insert a Ceramic Probe into the Drip Watering System. Manufactured from robust black plastic. Barbed at on all three sides to hold the tube securely in place. Dimensions: (1.5cm) long on the two  sides, 5/16" (8mm) long on the 1/16" side. Buy Tropf Blumat In-Line Connector J (3517)

Tropf Blumat End-Line Connector K (3512)

Insert a Tropf Blumat End-Line Connector where you wish to insert a Ceramic Probe at the end of a length of a run of  tube. Use where you need to insert a Ceramic Probe into the Drip Watering System. Manufactured from robust black plastic. Barbed at on both sides to hold the tube securely in place. Dimensions: (1.5cm) long on the side, 5/16" (8mm) long on the 1/16" side. Buy Tropf Blumat End-Line Connector K (3512)

Tropf Blumat 1/16" T Connector L (3412)

Divert water into three different drip areas with this Tropf Blumat 1/16" to 1/16" Fitting. Manufactured from robust black plastic. Barbed at on all three sides to hold the 1/16" tube securely in place. Dimensions: 5/16" (8mm) long on all three sides. Buy Tropf Blumat 1/16" T Connector L (3412)

Tropf Blumat 1/4" Feed Tube (MTR) D

This black, 1/4" flexible tubing forms the main 'artery' of the Tropf Blumat Watering System, carrying the water supply around the area to be watered. Strong & flexible enough to transport the water over large areas it can be held securely in place with either ¬" Stakes (to hold the tube in position in soil) or 'saddle clamps' (to hold the tubing against a house wall - available from most DIY stores). To turn corners without obstructing the flow of water you can purchase 'Elbow Connectors' or to connect into the ¬" tubing with another ¬" tube 'T Connectors' are available. Relatively unobtrusive, the black tubing prevents algae growth which can form in watering systems operating with clear tube. Supplied in continuous lengths (up to 50m) simply purchase as many metres as required. Buy Tropf Blumat 1/4" Feed Tube (MTR) D

Tropf Blumat 1/16" Drip Tube (Metre) (3508)

A flexible, brown 1/16" Drip Tube which is used in the Tropf Blumat system to carry water from the 1/4" Feed Tube up to & through the top of the Probe, from where the water will drip. It is possible to use up to a maximum of 1 metre of the Drip Tube at any one Probe, allowing the water coverage of the system to be extended by the use of Drippers. A maximum of 5 Drippers can be placed in 1 metre of the Drip Tube. Supplied in continuous lengths simply purchase as many metres as required. Buy Tropf Blumat 1/16" Drip Tube (Metre) (3508)

Tropf Blumat 1/4" Stakes (5) H

These Tropf Blumat Stakes will hold the 1/4" tubing securely in place - ideal for using in hanging baskets, pots & containers. Simply push the 1/4" tubing into the top section of the stake. Sink the 3«" (9cm) spike of the stake into the ground. Supplied as a pack of five stakes. Buy Tropf Blumat 1/4" Stakes (5) H